A10vso Series Hydraulic Pumps Best Supplier for Rexroth Piston Pump A10vso18, A10vso28, A10vso45, A10vso60, A10vso85, A10vso100, A10vso140

• After-sales Service: 12 Months
• Warranty: 12 Months
• Structure: Single Cylinder
• Shipping Cost: Estimated freight per unit.: about shipping cost and estimated delivery time.
• Currency: US$
• Return&refunds: You can apply for a refund up to 30 days after receipt of the products.
• Model NO.: A10VSO
• Power: Hydraulic
• Application: Machinery Manufacturing
• Performance: Corrosion
• Standard: Standard
• Apply: Paver
• Apply for: Drum Roller
• Material: Cast Iron
• Power Type: Hydraulic
• Usage: Oil
• Driving Type: Hydraulic
• Transport Package: Standard Export Package
• Specification: A10VSO
• Trademark: PX
• Origin: China
• HS Code: 8412291000
• Production Capacity: 500pieces/Month

Product Description

Type code Type code

01         02            03           04           05                          06           07                          08           09           10           11           12           13

A10V(S)

O

/

31

-

V

Version                                                                                                                                                                  18     28     45     71     88    100   140

01

Standard version (without code)

High-speed version (external dimensions are the same as the standard version)

-

-

-

H

Axial piston unit

02

Swashplate design, variable, nominal pressure 280 bar, maximum pressure 350 bar

-

-

-

-

-

-

A10VS

-

A10V

Operating mode

03

Pump, open circuit

O

Size (NG)

04

Geometric displacement, see table of values on pages 6 and 7

18

28

45

71

88

100

140

Control device

05

Two-point control, direct operated

DG

Pressure controller                 hydraulic

DR

with flow controller            hydraulic

X-T open

DFR

X-T plugged with flushing function

DFR1

X-T plugged without flushing function

DRSC

with flow and differential pressure control, electrically variable

EF1)

with pressure cut-off

hydraulic       remote controlled

DRG

electrical       negative control

U = 12 V

ED71

U = 24 V

ED72

electrical       positive control

U = 12 V

ER71

U = 24 V

ER72

Pressure-flow power control

-

DFLR

Series

06

Series 3, index 1

31

Direction of rotation

07

Viewed on drive shaft

clockwise

R

counter-clockwise

L

Sealing material

08

FKM (fluoroelastomer)

V

Drive shaft                                                                                                                                                            18     28     45     71     88    100   140

09

Splined shaft ANSI B92.1a

standard shaft

S

similar to shaft "S" however for higher input torque

-

-

R

reduced diameter, limited suitability for through drive (see table of values, page 9)

○

U

same as "U", higher torque; limited suitability for through drive (see table of values, page 9)

-

W

Mounting flange

10

ISO 3019-1 (SAE)

2-hole

C

4-hole

-

-

-

-

-

-

D

1)   See data sheet 92709

 

Type code
01         02            03           04           05                          06           07                          08           09           10           11           12           13
	A10V(S)	O				/	31			-	V
Working port                                                                                                                                                       18     28     45     71     88    100   140
11	SAE flange ports according to J518 Working ports metric			Fastening thread metric; rear				not for through drive					-				-	-				11
													-	-		-			-	-		41
				Fastening thread metric; lateral top bottom				for through drive									-	-				12
													-	-		-			-	-		42
	SAE flange ports according to J518 Working ports UNF			Fastening thread UNF; rear				not for through drive					-				-	-				61
													-	-		-			-	-		91
				Fastening thread UNF; lateral top bottom				for through drive									-	-				62
													-	-		-			-	-		92
Through drive (for mounting options, see page 53)
12	Flange ISO 3019-1                  Hub for splined shaft2) Diameter                                Diameter												18     28     45     71     88    100   140
	without through drive																					N00
	82-2 (A)			5/8 in     9T 16/32DP																		K01
				3/4 in     11T 16/32DP																		K52
	101-2 (B)			7/8 in     13T 16/32DP									-									K68
				1 in         15T 16/32DP									-	-								K04
	127-2 (C)			1 1/4 in  14T 12/24DP									-	-		-						K07
				1 1/2 in  17T 12/24DP									-	-		-	-	-				K24
	152-4 (D)                               1 3/4 in  13T 8/16DP												-	-		-	-	-	-			K174)
Connectors for solenoids3)
13	Without connector (without solenoid, with hydraulic control only, without code)
	DEUTSCH - molded connector, 2-pin, without suppressor diode																					P
=  Available       ○   =  On request      -  =  Not available
Notice    Note the project planning notes on page 59.    In addition to the type code, please specify the rel- evant technical data when placing your order.

Hydraulic fluids Hydraulic fluids

The A10V(S)O variable pump is designed for operation with HLP mineral oil according to DIN 51524. Application instructions and requirements for hydraulic fluids should be taken from the following data sheets before the start of project planning:    90220: Hydraulic fluids based on mineral oils and related hydrocarbons    90221: Environmentally acceptable hydraulic fluids    90222: HFD hydraulic fluids (for permissible technical data, see data sheet 90225)

Notes on selection of hydraulic fluid The hydraulic fluid should be selected such that the operat- ing viscosity in the operating temperature range is within the optimum range (νopt see selection diagram). Notice At no point of the component may the temperature be higher than 115 °C. The temperature difference specified in the table is to be taken into account when determining the viscosity in the bearing. If the above conditions cannot be maintained due to extreme operating parameters, please contact the respon- sible member of staff at Bosch Rexroth.

Viscosity and temperature of hydraulic fluids

Viscosity

Temperature

Comment

Cold start                     νmax ≤ 1600 mm2/s

θSt ≥ -40 °C

t ≤ 1 min, without load (p ≤ 30 bar), n ≤ 1000 rpm

Permissible temperature difference

ΔT ≤ 25 K

between axial piston unit and hydraulic fluid

Warm-up phase             ν < 1600 to 400 mm2/s

θ = -40 °C to -25 °C

Note the detailed information on operation with low tempera- tures, see data sheet 90300-03-B

Continuous operation   ν = 400 to 10 mm2/s

this corresponds, for VG 46 for example, to a temperature range of +5 °C to +85 °C (see selection diagram)

θ = -25 °C to +110 °C

measured at port L, L1 observe the permissible temperature range of the shaft seal

(ΔT = approx. 5 K between the bearing/shaft seal and port L, L1)

νopt = 36 to 16 mm2/s

Range of optimum operating viscosity and efficiency

Short-term operation    νmin  7 mm2/s

t < 1 min, p < 0.3 • pnom

Selection diagram

Maximum permissible viscosity for cold start

1600 1000 600

Warm-up phase

Minimum permissible viscosity for short-term operation

7 -40

-25

-10

0    10

30        50

70       90

115

Temperature θ [°C]

X-T plugged without flushing function

Filtration of the hydraulic fluid
Finer filtration improves the cleanliness level of the hydrau- lic fluid, which increases the service life of the axial piston unit.
A cleanliness level of at least 20/18/15 is to be maintained according to ISO 4406.
At very high hydraulic fluid temperatures (90 °C to maxi- mum 115 °C), cleanliness level 19/17/14 according to at least ISO 4406 is necessary.
Please contact us if the above classes cannot be observed.

Our advantages:
1. We are doing stock trad over 10 years , shipping more faster with good price 
2. We are professional supplier of hydraulics motor and pump also spare parts .
3. Our factory is more than 10 years exprience production  hydraulic motor pumps factory .
4.  we also dealer brand such as Rexroth  DANFOSS  Eton . 

Conpany introduction:
We are a professional supplier of  A2FM, A2FO, A6VE, A6VM, A7VO, A8VO, A10VSO, A4VG, A10VG series hydraulics for more than 10 years. There are many products available in stock. If you are going to purchare other brands hydraulics, we have Chinese brands for your consideration.








Workshop show:

Field of application:



We are offer  thiese machines  



We are offer these Brand 





Package:

Delivery:

Delivery time:

We have huge quantity of inventory for complete pumps, motor and some spare parts, 
so the leading time is within 3days if have in stock. 
If haven't, within 5days if the quantity is less than 50pcs. 
It depends on the quantity ordered.

Min. Order:
If the model is common or the production in our stock warehouse, there is No MOQ for stocking production.
Larger quantity, price will be more favorable.

Deliever Way:

By courier, like the DHL, UPS, Fedex,etc. It's door to door or barn to the door,
usually 5-7 days to arrive.

By air to air port, usually 3-5 days to arrive

By sea to sea port, usually 20-30 days to arrive.

If your deliever time is very urgent, we suggest that you choose by courier or air.

If not, it's very cheap to by sea.